After all these years, you would think that Nexon would make MapleStory playable on Mac OS. Unfortunately, this is not the case. I have been playing Maplestory for almost 10 years, and throughout these 10 years I hadn’t figured out how to play MapleStory on a Mac – until now!
You want to clone your disk not image it. There are dozens of applications you can run to do this or you can even buy hardware to do it. Boot from external drive and run one. You can use OSX or Linux and use dd. Or boot from Macrium repair disk (free Windows software) and clone it. None care about the data on the drive be it Windows or OSX or Linux and copy your partitions and partition table just fine. Just make sure your destination disk is as big or bigger as your internal one.
I've used both methods and both work fine on all my Macs (and PCs). Your only consideration is what external device your Mac will boot from. Older ones (like my 2006 MBP) will not boot Windows software from external USB without a boot loader. I therefore use either OSX or Linux normally. None are that fast mind you but they are free and you end up with an exact copy of your disk that is bootable in both OS. I don't know why MacOS people like recommending WinClone, CCC and Paragon.
There is no point paying for software to do such a trivial (OS agnostic) task. You could have a look at these to explain dd and Macrium. Or if your Mac will boot from USB then this is by far the easiest way. So the Bootcamp cloning process involve creating a separate NTFS partition on the backup drive first, then running the cloning software (which, unlike most regular Mac software can read/write the NTFS format)? I was hoping I'd find something which would just clone the entire drive (both partitions) in one go. I was also hoping for a free solution (my Mac is due for repairs and I'd like to make it easy to reinstall everything as it was when I get it back), so I ended up download (turns out 'free' meant a 10 day trial version).
Anyway I cloned the Mac drive first using Chronosync (which I use for all my backup needs), then ran the above which I understand creates a disk image file of the Windows partition. I assume to restore it I need to first have an empty Windows partition available on the Mac hard drive. I'm sure I'll find out when I get the computer back.
In hindsight I should probably have partitioned the backup drive so that I'd have both a Mac and a Windows (Bootcamp) partition which I'm guessing should have made cloning the Bootcamp partition easier as well. Doynton: is this what you meant when talking about free solutions such as DD or Macrium repair disk?
You mentioned that it won't be possible to boot Windows software from an external drive. Well, I don't mind as long as I can clone the drive (both partitions) back to the Mac as it was before, and I can carry on booting into OSX or Bootcamp as I like. I won't be using the external drive for anything else than a backup to restore from.
If all fails it's no biggie. My Mac partition is safely backed up and I only use Windows occasionally for a Windows-only app, so it's just a matter of re-installing Windows from scratch and that app. Click to expand.No. Everything is done from the Mac side. First you create a Winclone image of your Bootcamp. The image file is stored on the Mac side. This contains your Windows installation and all data and settings) To restore the image you create a MS-DOS FAT partition on the Mac using Disk Utility.
(max four partition allowing for RP and EFI and BC) Then, still running Winclone from the Mac side, you restore the Winclone Image to the MS-DOS FAT partition. You have to turn off SIP before restoring, and back on again afterwards.
If you want to restore the image to a different computer you have to run Sys Prep in Windows before making the image to remove all the drivers, which will be wrong for the new computer. More here: Winclone support is very good. Everything is done from the Mac side. First you create a Winclone image of your Bootcamp. The image file is stored on the Mac side. This contains your Windows installation and all data and settings) To restore the image you create a MS-DOS FAT partition on the Mac using Disk Utility. (max four partition allowing for RP and EFI and BC) Then, still running Winclone from the Mac side, you restore the Winclone Image to the MS-DOS FAT partition.
You have to turn off SIP before restoring, and back on again afterwards. If you want to restore the image to a different computer you have to run Sys Prep in Windows before making the image to remove all the drivers, which will be wrong for the new computer. More here: Winclone support is very good. Click to expand.There is a bit of a risk in this but I believe it will be OK.
I have changed the drive within the same machine and restored with Winclone successfully in the past. If it was me I would just do it. If it fails to boot you can always go back to the original hard drive and start again. If you are nervous about doing this I would email Winclone Support with the specifics and see what they say. Probably the cast-iron method would be:- Winclone image of your BC as it is now (for fall back if the rest goes wrong) Boot up from Bootcamp and run sysprep Make another Winclone image of the sysprep'd Bootcamp Restore the sysprep'd image to the new SSD Reinstall Bootcamp driver package. (need to download this separately) I have never used sysprep, and the above seems like overkill for changing the drive in the same computer. Note that if you are restoring the image to a smaller partition than the original you need to.
It all seems quite complicated (except the physical hard drive copy/clone dock doing a block copy of the drive). For now I've decided to do a fresh re-install of everything on the hard drive since the computer was in for hard drive related repairs, and my clone copy would potentially contain errors because of reading errors. As I use Chronosync for my backup needs (in addition to Time Machine) I'm going to look into (or suggest a new feature) doing backups of Windows partitions. That would make life a lot easier. By the way, are there any good FAQs on installing Bootcamp?
I struggled a lot with it and don't really understand how it got installed. It would be nice to do it correctly this time. I have a Mac Pro 6 Core early 2014 trashcan Mac with a 256 GB internal SSD with macOS High Sierra and a Windows 10 Boot Camp partition. I use CCC and Time Machine for the macOS partition. To back up the Boot Camp partition I do the following: I simply run the free version of MiniTool Partition (I use version 9.1) from within Boot camp and select 'Copy Disk Wizard' and select an attached external SSD.
It's simply a couple of clicks. Once done to make the new clone bootable I simply run the Free EasyUFI App from Boot Camp and repair the EFI on the new clone.
Now I have a bootable back up of Windows 10 made from my Boot Camp partition. Easy and Free. Click to expand.Hello Weaselboy Since you have technical knowledge (including how to take advantage of the Terminal procedures) and unfortunately I do not have them. Would you be so kind to read my thread 'Need help to install Windows in a MP 6.1'? It is in this section of the Forum.
I must be doing things in the wrong way since I do not manage to perform that task no matter how hard I try I apologize to use your time but do not know what to do without the advise of a knowing person like you. Thank you very much in advance!